"Fossies" - the Fresh Open Source Software Archive

Member "openssl-1.0.2q/doc/ssl/SSL_write.pod" (20 Nov 2018, 4126 Bytes) of package /linux/misc/openssl-1.0.2q.tar.gz:


Caution: As a special service "Fossies" has tried to format the requested pod source page into HTML format but links to other pod pages may be missing or even errorneous. Alternatively you can here view or download the uninterpreted pod source code. A member file download can also be achieved by clicking within a package contents listing on the according byte size field. See also the last Fossies "Diffs" side-by-side code changes report for "SSL_write.pod": 1.1.0g_vs_1.1.1-pre2.

NAME

SSL_write - write bytes to a TLS/SSL connection.

SYNOPSIS

 #include <openssl/ssl.h>

 int SSL_write(SSL *ssl, const void *buf, int num);

DESCRIPTION

SSL_write() writes num bytes from the buffer buf into the specified ssl connection.

NOTES

If necessary, SSL_write() will negotiate a TLS/SSL session, if not already explicitly performed by SSL_connect(3) or SSL_accept(3). If the peer requests a re-negotiation, it will be performed transparently during the SSL_write() operation. The behaviour of SSL_write() depends on the underlying BIO.

For the transparent negotiation to succeed, the ssl must have been initialized to client or server mode. This is being done by calling SSL_set_connect_state(3) or SSL_set_accept_state() before the first call to an SSL_read(3) or SSL_write() function.

If the underlying BIO is blocking, SSL_write() will only return, once the write operation has been finished or an error occurred, except when a renegotiation take place, in which case a SSL_ERROR_WANT_READ may occur. This behaviour can be controlled with the SSL_MODE_AUTO_RETRY flag of the SSL_CTX_set_mode(3) call.

If the underlying BIO is non-blocking, SSL_write() will also return, when the underlying BIO could not satisfy the needs of SSL_write() to continue the operation. In this case a call to SSL_get_error(3) with the return value of SSL_write() will yield SSL_ERROR_WANT_READ or SSL_ERROR_WANT_WRITE. As at any time a re-negotiation is possible, a call to SSL_write() can also cause read operations! The calling process then must repeat the call after taking appropriate action to satisfy the needs of SSL_write(). The action depends on the underlying BIO. When using a non-blocking socket, nothing is to be done, but select() can be used to check for the required condition. When using a buffering BIO, like a BIO pair, data must be written into or retrieved out of the BIO before being able to continue.

SSL_write() will only return with success, when the complete contents of buf of length num has been written. This default behaviour can be changed with the SSL_MODE_ENABLE_PARTIAL_WRITE option of SSL_CTX_set_mode(3). When this flag is set, SSL_write() will also return with success, when a partial write has been successfully completed. In this case the SSL_write() operation is considered completed. The bytes are sent and a new SSL_write() operation with a new buffer (with the already sent bytes removed) must be started. A partial write is performed with the size of a message block, which is 16kB for SSLv3/TLSv1.

WARNING

When an SSL_write() operation has to be repeated because of SSL_ERROR_WANT_READ or SSL_ERROR_WANT_WRITE, it must be repeated with the same arguments.

When calling SSL_write() with num=0 bytes to be sent the behaviour is undefined.

RETURN VALUES

The following return values can occur:

> 0

The write operation was successful, the return value is the number of bytes actually written to the TLS/SSL connection.

<= 0

The write operation was not successful, because either the connection was closed, an error occurred or action must be taken by the calling process. Call SSL_get_error() with the return value ret to find out the reason.

SSLv2 (deprecated) does not support a shutdown alert protocol, so it can only be detected, whether the underlying connection was closed. It cannot be checked, why the closure happened.

Old documentation indicated a difference between 0 and -1, and that -1 was retryable. You should instead call SSL_get_error() to find out if it's retryable.

SEE ALSO

SSL_get_error(3), SSL_read(3), SSL_CTX_set_mode(3), SSL_CTX_new(3), SSL_connect(3), SSL_accept(3) SSL_set_connect_state(3), ssl(3), bio(3)