"Fossies" - the Fresh Open Source Software Archive  

Source code changes of the file "doc/sdparm.8" between
sdparm-1.11.tgz and sdparm-1.12.tgz

About: sdparm let you access SCSI modes pages, read VPD pages, send simple SCSI commands (similar functionality for SCSI disks like "hdparm" for ATA disks).

sdparm.8  (sdparm-1.11.tgz):sdparm.8  (sdparm-1.12.tgz)
skipping to change at line 696 skipping to change at line 696
used. used.
29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "T his status shall be returned if a 29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "T his status shall be returned if a
command is aborted by a command or task management function on another I_T nexus and the Control command is aborted by a command or task management function on another I_T nexus and the Control
mode page TAS bit is set to one". mode page TAS bit is set to one".
33 the command sent to DEVICE has timed out. This occurs in Linux onl y; in other ports a command time- 33 the command sent to DEVICE has timed out. This occurs in Linux onl y; in other ports a command time-
out will appear as a transport (or OS) error. out will appear as a transport (or OS) error.
40 the command sent to DEVICE has received an "aborted command" s ense key with an additional sense 40 the command sent to DEVICE has received an "aborted command" s ense key with an additional sense
code of 0x10. This group is related to problems with protection in formation (PI or DIF). For exam- code of 0x10. This value is related to problems with protection in formation (PI or DIF). For exam-
ple this error may occur when reading a block on a drive t hat has never been written (or is ple this error may occur when reading a block on a drive t hat has never been written (or is
unmapped) if that drive was formatted with type 1, 2 or 3 protecti on. unmapped) if that drive was formatted with type 1, 2 or 3 protecti on.
48 this is an internal message indicating a NVMe status field (SF) is other than zero after a command 48 this is an internal message indicating a NVMe status field (SF) is other than zero after a command
has been executed (i.e. something went wrong). Work in this area is currently experimental. has been executed (i.e. something went wrong). Work in this area is currently experimental.
49 low level driver reports a response's residual count (i.e. number of bytes actually received by HBA 49 low level driver reports a response's residual count (i.e. number of bytes actually received by HBA
is 'requested_bytes - residual_count') that is too high. So no use ful processing can be done with is 'requested_bytes - residual_count') that is too high. So no use ful processing can be done with
that response. that response.
skipping to change at line 746 skipping to change at line 746
Most of the error conditions reported above will be repeatable (an exampl e of one that is not is "unit Most of the error conditions reported above will be repeatable (an exampl e of one that is not is "unit
attention") so the utility can be run again with the -v option (or severa l) to obtain more information. attention") so the utility can be run again with the -v option (or severa l) to obtain more information.
AUTHORS AUTHORS
Written by Douglas Gilbert. Written by Douglas Gilbert.
REPORTING BUGS REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>. Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT COPYRIGHT
Copyright © 2005-2020 Douglas Gilbert Copyright © 2005-2021 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warra nty; not even for MERCHANTABILITY This software is distributed under a FreeBSD license. There is NO warra nty; not even for MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE. or FITNESS FOR A PARTICULAR PURPOSE.
WEB SITE WEB SITE
There is a web page discussing this package at http://sg.danny.cz/sg/sdpa rm.html . There is a web page discussing this package at https://sg.danny.cz/sg/sdp arm.html .
SEE ALSO SEE ALSO
hdparm(hdparm), sg_modes, sg_wr_mode, sginfo, sg_inq, sg_vpd(all in sg3 _utils), smartmontools(smartmon- hdparm(hdparm), sg_modes, sg_wr_mode, sginfo, sg_inq, sg_vpd(all in sg3 _utils), smartmontools(smartmon-
tools.sourceforge.net), mt, eject(eject), tools.sourceforge.net), mt, eject(eject),
sdparm-1.11 March 2020 SDPARM(8) sdparm-1.12 April 2021 SDPARM(8)
 End of changes. 4 change blocks. 
3 lines changed or deleted 3 lines changed or added

Home  |  About  |  Features  |  All  |  Newest  |  Dox  |  Diffs  |  RSS Feeds  |  Screenshots  |  Comments  |  Imprint  |  Privacy  |  HTTP(S)